China
HomeHome Resources Industry News

How to Improve the Design and Manufacturing Level of Water Pumps

Industry News 2026-09-17 pump designpump manufacturingthree-dimensional flowCFDimpeller retrofit
Although Chinese-made pumps dominate the domestic market, gaps in design concepts, materials and new technology still limit their competitiveness abroad.

At present, pumps independently designed and produced in China have achieved great success in the domestic market, occupying almost the vast majority of market share, but in foreign markets Chinese-designed and manufactured pumps are still difficult to break into. The reason is that there are still some gaps between Chinese-designed pumps and the international leading level. This article starts with an analysis of the current status of pump research at home and abroad, proposes feasible measures for pump improvement, and provides theoretical support for China's independent pump technology to reach or exceed the international level.

Concept image of pump performance

1 Current status of pump technology development in China

At the present stage, the forms of pump production and the drawings and models in China mainly include joint design, introduction and independent development; the pumps used in China's market and industry are basically designed and manufactured by these means and are the leading products in the domestic market, but the design level and technology of these products still lag somewhat behind the international advanced level. For example, few pumps produced in China are completely independent designs; they are often copies or references to foreign drawings, lacking the flexibility and ingenuity of independent research and development and having little scalability. This also causes Chinese manufacturers to lack independent awareness and flexible thinking in the process of pump production and design, unable to break through the existing design frameworks and form their own unique design concepts and technologies. If one only modifies and improves on the basis of others' work without the free and bold thinking of foreign designers, there will be no great progress or breakthrough. In addition, although domestically designed and produced pumps have low cost and quickly occupied the domestic market, they are still absent from the international market.

2 Current status of advanced pump technology abroad

In some countries with more advanced technology, there is a unified concept for pump design: design aims at ingenious mechanisms, flexible design thinking, independent design awareness, and paying as much attention to pump materials as to pump structure. For example, Italy is very particular about the materials used in pumps, and stainless steel housings must meet certain standards before they can be used, while Japan has very high requirements for details when designing and manufacturing pumps, producing very refined pumps.

Compared with domestic research, foreign pump research and design leads mainly in the following aspects:

1) Large-capacity computer accurate prediction technology and model computer design technology;

2) An important achievement in pump development and research on cavitation, namely that the degree of cavitation damage to flow passage components dE/dt has the following exponential relationship with the bubble length L of the pump: dE/dt=K, and there are approximate calculation methods for bubble length;

3) Vibration characteristics of pumps are studied from two directions, with certain results achieved;

4) An inverse function transfer method is introduced to measure pump vibration values and then obtain the external force characteristics of the impeller;

5) In design, foreign countries pay more attention to the dynamic characteristics of the impeller and to cavitation research, and the invention and application of the magnetic shaft achieved a major technical breakthrough in the pump field;

6) Computer-based solid modelling technology for mechanical parts, which is of obvious significance for improving design level.

3 Feasible measures to improve the design performance of Chinese pumps

In recent years, China's pump design and manufacturing technology has made great progress, and some designs have approached the international leading level, but there are still gaps in many aspects of pump design and manufacturing, such as design concepts, mechanical materials and new design and manufacturing technologies. Therefore, in the process of pump research and design in China, we should first adjust our mindset and establish correct concepts, and then conduct in-depth research and development on materials and technology.

3.1 Impeller improvement

The impeller is the heart of a water pump; it determines the head and efficiency of the pump. When operating conditions and design differences are not great, the pump casing has little influence on pump performance, so improving the impeller is particularly important. First, advanced foreign large-capacity computer accurate prediction technology can be introduced, and professional personnel organized to study it in detail. Through this technology, model prediction and design of the pump impeller can be carried out; in addition, finite element calculation and experimental modal analysis can be used to calculate and analyse the dynamic characteristics of the impeller, and modal confidence and eigenvalue sensitivity modification theory can be introduced to provide a dynamics-based design method for impeller improvement. In addition, to extend impeller service life, besides improving pump cavitation performance, high-quality materials such as 1Cr13Ni4Mo stainless steel can be used.

The concept of technical improvement of pump impellers should focus mainly on flexibility and adaptability. In view of internationally advanced technologies such as CFD and three-dimensional flow, relevant Chinese institutions and departments should increase R&D investment and establish professional R&D teams and personnel training mechanisms and systems to continuously supply talent for pump technology research and development.

3.2 Introducing three-dimensional flow technology

As early as 1976, the authoritative American reference book Pump Handbook already analysed in detail the three-dimensional flow theory created by the Chinese scientist Wu Zhonghua, and considered that this technology would certainly develop into a leading technology in the pump design and manufacturing industry. In 1986, the jet-wake three-dimensional flow calculation method began to be applied in pump design. With the development of this technology, China and other advanced countries in the world are now studying and using it in depth. It can be said that this is one of the few technologies in which China leads other countries in pump technology, so it must not be left out in China's pump design and manufacturing.

The "jet-wake" phenomenon was first discovered in aviation centrifugal compressors and observed by laser velocimetry. As shown in Figure 1, the curved lines dh and cg represent two adjacent impellers, dc and hg are the inlet and outlet respectively, W1 and W2 represent the flow velocities at the inlet and outlet, t is the flow separation point, htv is the wake region, and cdtvg is the jet region. However, there is currently no accurate method for calculating the wake. Owing to viscosity and pressure gradients, fluid separates along the blade suction surface and the front cover surface at the impeller outlet, forming a wake region. Only through "jet-wake three-dimensional flow" calculation can quantitative analysis be obtained, thereby improving pump performance.

Three-dimensional flow impeller improvement technology actually uses leading pump design software to re-optimize the hydraulic components inside the pump, so that flow and pressure can be increased without changing the motor, pump casing or piping, thereby improving pump efficiency. As shown in Figure 2, the installation dimensions of the two impeller designs (shaft hole, key, seal ring) are the same, but the blade shape has changed greatly: the widening of the meridional-to-three-dimensional flow blades increases flow capacity, and the reduction in diameter relatively increases the outlet width. At the same time, the inlet edge of the three-dimensional flow blade extends toward the incoming flow, reducing inlet losses. Therefore, the impeller improved by three-dimensional flow calculation technology is more reasonable.

3.3 Research and application of CFD technology

The research focus of computational fluid dynamics (CFD) technology is to use numerical calculation methods to solve the mathematical equations governing fluid flow by computer. At present, general research in the industry roughly considers three levels: basic numerical methods, numerical calculation supplemented by experiments, and solving practical engineering problems. The more advanced applications at home and abroad are mainly concentrated at the second level. CFD technology can effectively reduce the number of actual tests and improve pump performance. When financial and professional support is insufficient, vigorously developing CFD technology by relying on science and technology and establishing a three-dimensional viscous numerical simulation software system can rapidly improve China's pump R&D level while reducing investment and cost, making it possible to bring China's pump design level to or ahead of the world's advanced level as soon as possible.

Researching and improving impeller mesh generation technology is the basic prerequisite for fluid flow numerical simulation and flow field modelling; mesh division is the basis for numerical discretization of flow governing equations and one of the key technologies for turbulent flow numerical simulation, directly determining the convergence of the solution and the accuracy of the results. R&D investment in impeller mesh generation technology should therefore be increased. In addition, the setting of boundary conditions is very important in the simulation of the internal flow field of a pump; inlet and outlet boundary conditions as well as periodic boundary conditions are all required for the computational domain. Using CFD computational fluid dynamics to analyse and study the internal flow field of a centrifugal pump is very important for understanding and mastering the internal flow laws of centrifugal pumps and for their design. This research content has very great development prospects in the pump industry, but it is also very complex work, so a correct understanding of CFD technology is needed and a reasonable and qualified combination of researchers is required. In addition, CFD technology is a technology involving multiple fields, so to give full play to the advantages of CFD technology in pump R&D, comprehensive factors must also be considered, with more theory combined with experiment, organically combining CFD numerical simulation with experiments and theory; only in this way can problems be solved ideally and effectively.

4 Main ideas for pump improvement

The main purpose of pump research and development is to reduce costs, improve pump efficiency, extend pump service life and minimize energy waste, in line with the main theme of energy saving and emission reduction advocated by the state. Although in recent years pumps produced in China have made great achievements and basically occupied the domestic market, compared with more advanced foreign pumps, the share of Chinese-made pumps in the international market is very low. Even though foreign pumps have higher cost and higher prices, foreign markets are more willing to choose those pump products because foreign-made pumps have more advanced technical content and higher pump efficiency and service life. Therefore, when independently developing pump products, China should take independent awareness, flexible thinking, high-quality materials and high technical content as the main R&D directions, so as to reach or even lead the world's advanced level in pump R&D and design

Related ArticlesRELATED NEWS

View More
WhatsApp
Top